METAL ROOFING INSTALLATION USING THE PANEL

 

 

Today we will mount an American Building Elements’ steel roofing panel. These instructions particularly concentrate on steel panel installation. To get more information concerning eave trim and also cleat setup, watch our other how-to video clips. The panel utilized in this instance is a 16-inch insurance coverage panel with a nail flange. We will certainly reveal you ways to install these steel panels with both revealed fasteners and surprise bolts.

 

Subjected Bolt Installment

 

Action 1: Begin Square

 

When you’re installing a steel roofing panel, the initial thing that you want to do is make certain you’re starting square. This means that your vertical lines are all running square to your eave.

 

It’s important to start square due to the fact that if the very first panel is tilted a bit, all the panels that come after are mosting likely to be slanted also. When you’re beginning the roofing, you wish to contest the side and change your panel if required. For example, if this particular roof covering was off a bit, also by simply half an inch, I would tilt our panel a little bit to make sure that we ran square, beginning with the first panel.

 

Action 2: Cut Panel to Size & Add Eave Trim

 

The panel we are making use of is as well long. When you’re doing a subjected fastener eave installment, you want to overhang the eave by one and a half or 2 inches at most. Put your tape up versus completion wall as well as measure down to the side of your eave trim. For this example, it’s specifically 24 inches, and also I’m going to include an inch and a half to that dimension and also cut my panel to size.

 

To do so, turn the panel over as well as make marks on the reverse side. I had claimed that the dimension was 24 inches which I should add an inch and also a half to that, so I’m going to make a mark at 25.5 inches. I’m going to do the exact same on the other side at 25.5 inches. Making use of a square or a straight side, you could after that join those two lines to develop your cut-line.

 

Next off, you need to puncture the man and the women rib to obtain to the level of the panel. Using my duckbill snips to guarantee a good tidy edge, I’m going to come through the flat of the pan. Make sure throughout this process that you are wearing your gloves. Last, cut the women rib. Now we have a panel that’s been reduced to 25.5 inches to make sure that 1.5 inches can overhang at the eave, and we prepare to install it.

 

Step 3: Use Sealer Tape

 

This panel is 25.5 inches long to ensure that 1.5 inches looms the eave, as well as in between the eave trim and also the bottom of the panel, we’re mosting likely to apply one row of sealant tape. Keep in mind, sealant tape goes between all layers of steel. Use the sealant tape along the facility of the whole eave as well as get rid of the tape backing.

 

Tip 4: Installment Using Subjected Fasteners

 

Now we can install our roof covering panels. See to it the panel is square to the eave of the roof covering to ensure that all panels installed after that are straight. Next, placed a screw right into the securing strip to maintain it stable prior to installing the screws along the face. Along the fastening strip of the SL16, always utilize the pancake head bolt. It’s the low-profile head that won’t dimple the following panel when it turns up, which is essential. Spaced at 12 inches from bolt to bolt, tighten them but do not over-tighten. Over-tightening draws the panel down and places stress into the panel.

 

Following you will mount exposed fasteners along the center of the frying pan, and make certain that the bolts string the sealant tape underneath to create a water tight seal. The screw we will make use of in the facility of the pan is a wood-grip. This is our neoprene washing machine bolt. It’s a paintinged bolt that matches the panel, and you’ll should ensure that it threads the sealant tape below the panel. Attach three fasteners, one on each side as well as one in the middle. Make sure to not over-tighten the bolt. If you do, it squishes out the neoprene washer which gets subjected to the sunlight. This creates it to dry as well as fracture much quicker. You could after that remain to affix and also install even more panels until the roofing system is covered.

 

Hidden Fastener Setup

 

Action 1: Set Up Offset Cleat

 

Install the countered cleat along the eave, then you are ready to install the steel roof panels. The offset cleat permits us to develop a true covert bolt setup. You can learn more regarding installing eave trim and also offset cleats in one more among our steel roof covering installation videos. I know one Miami roofing company.

 

Step 2: Bend Panel Side

 

We will certainly prepare completion of this panel by reducing up one inch on either side, folding under, and also eliminating these 2 ribs. This will permit us to install this panel and also clip it right into the offset cleat, making our bolts completely concealed.

 

Do this by moving the hemming device over and also flexing under one inch. This creates a real 180-degree bend. Next off, cut the male rib back a quarter of an inch to ensure that if it is sticking past a bit, it doesn’t keep the following panel from turning up flush with the edge of the cleat.

 

Step 3: Setup Using Hidden Fasteners

 

Since we have actually placed the one-inch clip on the metal panel and reduced the ribs back flush, we can install the panel by clipping it into the offset cleat. Glide the side up via the countered cleat to make sure that it is fulling involved as well as flush along the edge. Ensure that the panel is sitting back from the side of the roofing by half an inch. If we were to place the cleat flush with the edge of the roof, any kind of jogging will certainly be visible from the ground.

 

Now that the panel’s been mounted, placed a fastener with the fingernailing flange using a pancake head screw. If you see that the edge of the roof covering is holding up a bit, use a block of wood with a towel on it and a rubber mallet to push it down to make sure that it’s nice and also flat to the roof-bed.